Digital Projection Introduces FUSION Processors - - State -of -the -art Low -Latency Warp and Blend Solutions

Digital Projection International announces the launch of their new near zero latency warp, blend and network control solutions.

ATLANTA, GA - June 23, 2010 - Digital Projection International, an Emmy® Award -winning manufacturer of high -performance projection systems, announces the launch of their new near zero latency warp, blend and network control solutions. The FUSION MD, Fusion 3D and FusionNet solutions provide the most advanced single and multi -channel warp and blend processing available for critical real -time applications needing low latency.


All three products can be employed with DPI's iVision, dVision, TITAN and LIGHTNING projector lines, ensuring that no matter what level of projector performance or resolution an application requires, DPI can provide a fully integrated, FUSION -powered warp and blend solution with near zero video latency.

High quality signal resizing typically incurs a small penalty of video signal latency. Since delaying audio to match video is easily accomplished, video latency does not present a problem for the vast majority of applications. However, for real -time applications, such as IMAG and live televised events, where live presenters and the projected images may be visible at the same time, or for simulation, where on -screen imagery must immediately respond to trainee input, video latency must be as close to zero as possible.

DPI's FUSION MD and FUSION 3D processors were created to specifically provide the most advanced multi channel warp and blend for these critical real -time applications. The advanced architecture of the FUSION processors results in video latency that equates to a just a few lines of single -video frame, amounting to near -zero latency. Considering the precise warp and blend being performed, the electronic transparency of the FUSION Processors is beyond compare.

From a system design perspective, one FUSION MD or FUSION 3D processor is dedicated to each projector in an application. The input source for each projector simply loops through the related FUSION processor, then into the projector. FusionNet, DPI's new network control application, provides complete access to all adjustments for both the projectors and the FUSION processors, by way of a single window desktop application. Warp, blend and projector alignments, for as many channels as the application requires, are intuitive and precise.

Specifics on the two FUSION processors include:

1) FUSION MD (minimum delay): High bandwidth, near -zero latency processor providing warp and blend for sources with resolution up to WUXGA (1920 x 1200) at 60 Hz, and outputs to projectors with native resolution up to WUXGA as well. This makes the FUSION MD the perfect warp and blend solution to match nearly any of DPI's projectors with native resolution of WUXGA or less. In order to assure the highest quality, there is no scaling in the FUSION MD processor, so optimally, the source input should match the native resolution of the projector. If the input resolution does not match the projector resolution, projector scaling can be applied after the required warp and blend has been achieved by the FUSION MD processor.

2) FUSION 3D: Extreme bandwidth, near -zero latency processor providing warp and blend for sources with resolution up to WQXGA (2560 x 1600) at 60 Hz, and outputs to projectors with native resolution up to WQXGA as well. This makes the FUSION 3D the perfect warp and blend solution to match DPI's recently -launched dVision 35 -WQXGA. Alternatively, the FUSION 3D can provide near -zero latency warp and blend for sources up to WUXGA resolution at 120 Hz, enabling it to support warp and blend for projectors being employed in the highest resolution high frame rate and 3D applications. This makes the FUSION 3D the perfect warp and blend solution to perform with any of DPI's iVision, TITAN or LIGHTNING 3D displays. Like the FUSION MD processor, there is no scaling, so optimally, the source input to the Fusion 3D processor should match the native resolution of the projector. If the input resolution does not match the projector resolution, projector scaling can be applied after warp and blend has been achieved by the Fusion MD processor.

The FUSION suite delivers powerful, application enabling capabilities that are surprisingly easy to implement. FusionNet seamlessly integrates the operation of the FUSION processors and the DPI projectors they serve, thus ensuring large projector arrays can be expertly aligned on complex -geometry projection surfaces by technicians or projectionists with a simple understanding of the FusionNet application.

To download high -resolution images, please use the following link: http://www.digitalprojection.com/news/zips/DPI_Fusion_infoComm10.zip



About Digital Projection International

Founded in 1989, Digital Projection International (DPI) has been instrumental in the development and application of Digital Light Processing™ technology by Texas Instruments for projection systems. DPI introduced the world's first 3 -chip DLP® projector in 1997, and has since delivered expert system engineering and world -class customer services, thus maintaining its position as a digital imaging pioneer.

DPI's groundbreaking projection research and development has garnered the admiration of industry professionals around the world. This has earned the company many awards, including two Emmy® Awards for Outstanding Achievement in Engineering Development by the Academy of Television Arts and Sciences. DPI remains the first and only projector manufacturer to win the coveted award.

Today, DPI manufactures and distributes an extensive line of ultra high -performance 3 -chip and single -chip DLP® projection systems. These projectors are the reference standard for demanding applications such as large -venue, live -event staging, fortune 5000, education, medical and scientific research, command and control, digital cinema, commercial entertainment, worship and elite home cinema.

Featured Product

ELK Products -C1M1 Dual-Path Alarm Communicators with Remote Services

ELK Products -C1M1 Dual-Path Alarm Communicators with Remote Services

C1M1 offers a truly significant reduction in transmission time in comparison to other communicators that rely on dial capture or data bus decoding. This can result in quicker response time to emergency situations which could save lives and assets. By providing both IP and cellular pathways, C1M1 provides the reliability installers are looking for in an alarm communicator. C1M1 eliminates port forwarding and extra fees for remote access. Installers can remotely upload/download programming changes to M1 controls over IP or cellular using ElkRP2. Consumers can control the M1 remotely via the free ElkLink mobile app and web portal, as well as eKeypad and M1 Touch Pro apps. Other IP-based software and interface partners can connect to the M1 control over the local network through C1M1. C1M1 also provides email/text notifications for arm, disarm, and alarm events. ELK-C1M14GSM supports GSM (AT&T/T-Mobile) networks and ELK-C1M1CDMA supports CDMA (Verizon) networks.