AudioSource® Debuts New Two -Channel and Subwoofer Amps at EH Expo Fall 2007

The AMP102, AMP110, AMP210, and AMP310 2-Channel Amps and the AMPSUB210 Subwoofer Amp Round Out AudioSource's Complete Line of Affordable Yet Versatile and Performance-Driven Home Audio Electronics

PORTLAND, Ore., Oct. 1, 2007 - AudioSource® is proud to announce that it will feature five new two -channel and subwoofer amplifiers at the 2007 Electronic House Fall Expo, held in Long Beach, Calif. from Nov. 7 -9 at the Long Beach Convention Center, booth 1257. The AMP102, AMP110, AMP210, and AMP310 two -channel amps and the AMPSUB210 subwoofer amp round out AudioSource's complete line of affordable yet versatile and performance -driven home audio electronics.


"Our new AudioSource amplifiers have 20 years of tremendously successful design and engineering history behind them, coupled with the addition of the latest available technologies," explained Stewart Millager, AudioSource director of engineering. "These new amps are ideal for use in audio and home theater systems where power and performance are desired to push passive speakers and subs to their limits so they, too, perform at their best."

AMP310, AMP210, and AMP110 include Triple -Darlington power amplifier stages with complementary 15A bipolar output transistors and high -current, low -distortion drive for complex real -world loudspeaker loads. Their fully symmetrical power amplifier topology is a dual -differential error amplifier with circuit linearity that preserves signal integrity and selectable mains voltage with IEC mains inlet for use in worldwide markets.

Common AMP102, AMP110, AMP210, AMP310, and AMPSUB210 features include:
• Black anodized brushed aluminum faceplate
• Line 2 auxiliary output
• SN Ratio: 100dBA
• Front panel level and balance controls
• Signal sensing "Power On"
• 12VDC "Trigger On"
• Rackmount ready (optional)

Features of the 2 -Channel AMP310 include:
• 8 Ohm Stereo: 150W
• 4 Ohm Stereo: 225W
• 8 Ohm Bridged: 450W
• MSRP: $899.99

Features of the 2 -Channel AMP210 include:
• 8 Ohm Stereo: 90W
• 4 Ohm Stereo: 125W
• 8 Ohm Bridged: 250W
• Speaker A/B switching
• MSRP: $699.99

Features of the 2 -Channel AMP110 include:
• 8 Ohm Stereo: 75W
• 4 Ohm Stereo: 110W
• 8 Ohm Bridged: 250W
• Speaker A/B switching
• MSRP: $449.99

Features of the 2 -Channel AMP102 include:
• 8 Ohm Stereo: 50W
• 4 Ohm Stereo: 75W
• 8 Ohm Bridged: 150W
• Speaker A/B switching
• MSRP: $249.99

Features of the AMPSUB210 subwoofer amplifier include:
• 8 Ohm Stereo: 200W
• 4 Ohm Stereo: 300W
• Provision for subwoofer -specific equalization module
• MSRP: $699.99

Due to continual product improvement, pricing and specifications subject to change without notice.

Rodin is located at 9200 North Decatur Street, Portland, Oregon, USA 97203. For more information, please call 503 -978 -3321, or visit www.rodinaudio.com

# # #

Featured Product

PureLink - HCE III TX/RX: 4K HDR over HDBaseT Extension System w/ Control and Bi-Directional PoE

PureLink - HCE III TX/RX: 4K HDR over HDBaseT Extension System w/ Control and Bi-Directional PoE

The HCE III Tx/Rx HDBaseT™ extension system offers full HDMI 2.0 compliance supporting HDR (High Dynamic Range) and 4K@60Hz with 4:4:4 chroma sampling. Featuring PureLink's proprietary Pr©cis codec, a light compression technology, the HCE III can transport Ultra HD/4K, multi-channel audio, and High Dynamic Range (10 bits support) content over a single CATx cable. The HCE III provides HDMI extension up to 130 feet (40 meters) at Ultra HD/4K and up to 230 ft. (70 meters) at 1080p over category cable with embedded multi-channel audio, CEC pass-through, bi-directional RS-232 and IR control, and PoE - all with zero loss and zero noise. The HCE III Tx/Rx also supports Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio plus LCPM (up to 192 kHz). Additionally, the low profile "slim box" enclosure design make the HCE III ideal for limited space installation environments, such as behind flat panel displays and video walls.