Educate yourself on how Wi-Fi works, make sure your site surveys are thorough, use tools and testing to help you design, and ask your vendor for help. Do all of these things, and you’ll be much more likely to install great Wi-Fi networks for satisfied, happy customers.

Installer Tips: Understanding Wireless AP Placement

Steven Crabb | Luxul

 

Deciding where to place access points in a wireless deployment is as much art as science. While a good site survey and some planning is essential, you may also need to experiment with AP placement in order to optimize Wi-Fi network performance.

Understanding site conditions is important because construction materials, layout, and RF interference from nearby properties can all affect wireless network performance. Understanding how Wi-Fi works, how it interacts with construction materials, and how to optimize placement will make for a more efficient and trouble-free installation, ensuring a better network for your customer.

 

Understanding Wi-Fi

Fundamentally, Wi-Fi is simply radio frequency energy. As with RF signals like FM radio or cell phone, Wi-Fi signals travel through the air and are absorbed or reflected by objects. The strength of transmitted signals decreases with distance.

Wi-Fi signal strength is expressed in dBm or decibel-milliwatt. As simply as possible, the dBm unit expresses a power ratio in decibels (dB) of measured power, relative to one milliwatt (mW). 0 dBm is equivalent to 1mW, while -3dBm is roughly half of 1mW. Explaining the dBm scale thoroughly is beyond the scope of this article, but for practical purposes, consider the signal strength guidelines illustrated in Figure 1.

Figure 1. Illustration of Wi-Fi signal strength expressed in dBm, from excellent (left) to poor (right).

 

As you can see, signal strength between -10 and -50 dBm is considered excellent. Signal strength between -50 and -60 dBm is “good”, while “fair” is -60 to -70 dBm. Anything less than -70 dBm is considered poor. When signal strength drops significantly below -70 dBm, applications and data throughput rates may become unreliable or fail entirely, even if a client says it’s still connected.

 

Site Conditions and Access Point Placement

Any material can block a Wi-Fi signal, but some are worse than others. Wood, drywall, and glass don’t affect the signal as much as brick, stone, or water. The worst materials for Wi-Fi transmission are ceramic, concrete, and metal. As you can imagine, a large concrete fireplace wrapped in metal lath and stone does a very good job of blocking Wi-Fi signals.

Figure 2 illustrates Wi-Fi signal propagation and how walls can absorb and reflect the signal. Note also how signals pass through walls better at perpendicular angles than they do at oblique angles. It’s also easy to see that the signal is mostly gone at the end of the space opposite the AP. In this case, the AP should be located more centrally, or a second AP should be added for best coverage at opposite ends of the property.

Macintosh HD:Users:ecrabb:Desktop:ipiq:wifi-attenuation-anim-slow.gif

Figure 2. Simulated visualization of Wi-Fi signal propagation. The color white represents the strongest signal nearest the AP, while dark blue and black represent little or no signal. Image credit: Jason M Cole, www.jasmcole.com.

 

Access Point Separation and Overlap for Ideal Roaming

When you’re designing a Wi-Fi network and determining where to locate APs, it helps to understand how devices roam from one AP to another. Each Wi-Fi client device determines when it will disconnect from an AP, how long it will stick with a weak signal until it tries to connect to another, and when it will notify the user about what’s happening.

The best way to improve roaming and overall network performance is to ensure your APs aren’t too far apart or too close together. When APs are too close together, clients may not connect to the nearest AP with the best signal, degrading roaming and overall wireless network performance. Conversely, if APs are placed too far apart, as a client roams, signal strength may drop below usable levels before the client can connect to an AP with more suitable signal strength, causing slow or interrupted connectivity.

In general, you should place APs to ensure adequate coverage, but not so far apart that there is no signal overlap. Adjacent AP signals should overlap enough that a client device has a good connection to the AP to which it is currently attached, but also sees the next-nearest AP.

Figure 3. Diagram illustrating two access points and a signal overlap of -60 to -70 dBm at the midway point between the two APs.

 

As you can see in Figure 3, roaming clients should ideally see signal strength of two overlapping APs in the range of -60 to -70 dBm at the midway point between two APs.

Keep this “not too close, not too far” idea in mind as you determine placement for best separation and overlap. For more on roaming and AP overlap, refer to the IPIQ in the June/July issue, Wireless Controllers and Roaming: What you need to know.
 

Testing and Tools

As you’re installing a customer’s system, or even before you begin design or installation, there are several third-party software tools you can use to help evaluate site conditions and network performance on your customer projects.

  • iPerf is a computer application that runs on Windows, Mac OS X, Linux and Android and measures network throughput, bandwidth, packet loss, and other TCP/UDP performance factors. (www.iperf.fr)

  • Speedtest runs in a browser or on Android and iOS devices and makes it easy to check Internet connection speed on wired and wireless LAN connections or to compare the two. (www.speedtest.net)

  • inSSIDer is available for both Windows and Mac and allows you to visualize your wireless environment and test Wi-Fi signal strength so you can modify AP settings and placement for optimal Wi-Fi performance (www.inssider.com).

  • Ekahau HeatMapper is a Windows application you can use to assist in the process of mapping and analyzing Wi-Fi coverage (www.ekahau.com).

 

Summary

Wireless access point placement is both art and science. Because construction style, materials, and site conditions vary from one project to the next, you can’t simply call your network equipment vendor and ask how many APs you’ll need for an install. However, you can provide good information about size, layout, and construction, and your vendor should be able to help you make better decisions about placement.

Educate yourself on how Wi-Fi works, make sure your site surveys are thorough, use tools and testing to help you design, and ask your vendor for help.  Do all of these things, and you’ll be much more likely to install great Wi-Fi networks for satisfied, happy customers.

 
 
 
Luxul

Luxul

Luxul offers a complete line of easy-to-deploy network solutions for residential and commercial projects. The Luxul family of products includes the industry's most flexible and powerful access points, wireless controller, routers and switches.

Other Articles

Case Study: Affordable HD Video Distribution For Small Business Owners
HD-over-IP offers scalability and flexibility at a price more customers can afford.
PoE (Power over Ethernet) Creatively Applied
Power over Ethernet is flexible, safe and reliable, and offers installers and customers a wide range of benefits. With all the exciting applications, PoE helps you address customers’ needs, while delivering a better, more manageable, and more flexible network.
CEDIA Interview with Clark Roundy, VP of Marketing at Luxul
Our expectation is that we come out of the show with marching orders and priorities for the coming year, while also having demonstrated to our installers that we have been listening as confirmed by the new products now or soon to be available.
More about Luxul

Comments (0)

This post does not have any comments. Be the first to leave a comment below.


Post A Comment

You must be logged in before you can post a comment. Login now.

Featured Product

MIDLITE® - Power Jumper IC™ HDTV & Sound Bar Power Relocation Kit with Interconnect

MIDLITE® - Power Jumper IC™ HDTV & Sound Bar Power Relocation Kit with Interconnect

The Power Jumper IC™ HDTV & Sound Bar Power Relocation Kit easily conceals power & A/V cables within the wall for a professional appearance. The kit is recessed and features a new low profile in-wall jumper that can be fed through 1" diameter holes. The metal strain relief bracket provides a solid connection for the interconnect. The kit comes prewired and does not require an electrician for installation. The Power Jumper IC™ is available in three options, HDTV, Sound Bar and HDTV & Sound Bar.