This article is a great troubleshooting tip based on the “tool of a thousand uses”, the good old tone generator, tone detector.

The A/V Troubleshooters

Grayson Evans | The Training Department

The A/V Troubleshooters

Author: Grayson Evans, Training Reels - Copyright 2008

The Training DeptThis article is a great troubleshooting tip based on the “tool of a thousand uses”, the good old tone generator, tone detector.   Everyone has (or should have) one of these in the tool bag.  They're typically used to locate cables you forgot to label, labeled incorrectly, or got cut somewhere during house construction. 

I Should Have Known This

I was teaching the CEDIA Advanced Boot Camp class a few months ago where part of the class team exercise is to hook-up a rack of A/V gear for a home theatre.  DVD player audio/video out through preamp, through 5-ch. EQ, to 5-channel amp., to surround speakers.   About 30 cables or so.  After hookup, visual checkout, and power-up, no audio to speakers.  Hmmm.   Everything looks good.  Proper inputs selected, modes set correctly, still no audio.  We had lots of hand tools but nothing to use as test equipment.   No iPod, no scope, nothing useful.   So the only choice was to start “shotguning” it by removing cables and rerouting signals, first from the DVD player directly to the amp, and so on.  Unfortunately, the interconnect cables were already dressed nicely, coiled, cable-tied, etc.   It took about an hour to finally figure out the EQ wasn’t working.  You have all had a similar experience sometime, usually with equipment in a rack where access to the cabling was difficult. 

After that exercise, I was thinking about what we could have used to troubleshoot this problem quicker.  If only we had a simple audio signal detector.  That night it came to me over a beer.   Of course, there was one sitting right in the lab only a few yards away!  I can’t believe I didn’t think of it!

Audio Signal Generator and Signal Detector

Better known as the cable signal generator/detector (or “toner”), these two devices are, in fact, the perfect audio (and even video) test gear.   And they’re cheap.  

Photo 1. Typical tone generator (with alligator clip leads) and tone detector.

The tone detector is a very high gain, high impedance audio amplifier that can be used to locate sources of both audio and NTSC video.   To find out whether an audio component is putting out a line-level audio signal, simply stick the probe end of the detector into the RCA jack (see photo 2).  

 


Photo 2.  To test for audio, just stick the tip of the probe into the jack.

You’ll definitely hear the audio.   You can also touch the tip to the end of a line-level audio cable to hear the music.  This trick also works to detect NTSC video except that what you hear will sound like a nasty noise (the horizontal/vertical sync pulses).   But that’s not all.   Want to know whether audio is getting to a speaker?  Simply hold the tip of the detector on the speaker cable or touch into the speaker terminals.

Most signal generators output a pair or alternating tones, something like 500 and 700 cycles.   Unfortunately, upon closer examination of these tones on a scope, they are anywhere from 6 to 10 volts peak-to-peak and a nasty square wave with high amplitude spikes.   You could inject this signal into an amp, but it might cause either amp or speaker damage if the amp was cranked up. Typical line level audio is about 1-3 volt peak.

Since we need to make an adaptor for the alligator clips on the end of the tone generator leads to an RCA stye plug, it’s a easy step to add a simple filter/amplitude reducer to make the tone generator signal more amp/preamp friendly. Figure 1 shows the schematic of the two resistors and a capacitor needed to do this. 

Figure 1. Schematic of simple tone generator adaptor. 
Two resistors and a capacitor.  Values are not critical.

All the parts are easily available at Radio Shack.  This filters out the high frequency components (spikes) of the toner signal and lowers it’s amplitude to less than 1 volt peak.   Photos 3 and 4 show the adaptor I built hooked to the tone generator, and a close-up of the component hook-up.  Simple.  I tested this with three different toners, two from Fluke and one from Ideal (seen in photo).  All work fine. Keep it in the tool bag or the bag that holds the toner/detector. 

Photo 3. Ideal tone generator hooked to the audio adaptor with the alligator clips. 
I built it with two RCA plugs for quick stereo testing.

Photo 4.  Close-up of the adaptor components.  The RCA cable center conductors connect to the junction of the two resistors, grounds go to the end on the left.


Next time you have a dead audio path, you can use the toner to work from the audio source component to the final amp, or use the signal generator from the amp and work backwards to the source. 

If you have any questions about anything in this article, drop me an e-mail at grayson@trainingdept.com  I will actually answer it!    Visit our web site SUPPORT page for additional TIP and articles at www.trainingdept.com


Comments (0)

This post does not have any comments. Be the first to leave a comment below.


Post A Comment

You must be logged in before you can post a comment. Login now.

Featured Product

Introducing the revolutionary Comelit Visto Smart Doorbell

Introducing the revolutionary Comelit Visto Smart Doorbell

The Visto Doorbell is a new Smart Doorbell from Comelit which combines a modern Italian design with all of the basic features you are looking for in a smart video doorbell. In fact, it is so smart that it can use the 2 wires from your existing doorbell and pass both the power and the data signals. This solves the common problem of having poor wifi coverage all the way at your front door. The Visto also has built in night vision, video recording on a SD card and in the cloud, motion detection, and multiple mounting options including an angle mount. The second thing we are introducing is the Visto Dealer referral program. Because we only sell through the Professional Distribution channel, we want to give our dealers who buy in that channel extra incentives to sell our product. For any security dealers or installers who go on our website www.vistodoorbell.com, and sign up for our program, we will offer the following: - Free referrals to customers in your area - Cashback program - 10% discount during the 1st month of the launch - Free Visto t-shirts and gear - A chance to win a trip for 2 to Venice, Italy Its that easy. Let us refer customer to you and get paid in the process. All while selling a wonderful Italian designed smart doorbell which is innovative and easy to install. So all dealers should protect the pro-channel and install products like the Visto which are made and sold only at your friendly local security and low voltage distributors.