Everything You Always Wanted to Know About Home Theater and Electronics Cooling, But Didn't Know What or Who to Ask

A Painless Primer on Cooling Electronic Components

Frank Federman | Active Thermal Management

A Painless Primer on Cooling Electronic Components
By Frank Federman, CEO - Active Thermal Management

Everything You Always Wanted to Know About Home Theater and Electronics Cooling, But Didn't Know What or Who to Ask

Most home theater components are designed to run in well-ventilated areas. Unfortunately, when installing several components in an enclosed area without adequate airflow, the combined heat from the various components will shorten the life and hamper the performance of many expensive components. This is where cooling products and systems can help. The three steps to successful cooling are ---

1. Identify the cooling problem and the product you need.

2. Decide how and where to install it.

3. Install it.

You'd probably like a little more detail, especially in steps 1 and 2, so here we go… … and I promise NO math, and absolutely NO thermodynamics!

A few opening comments -----

There are formulas that determine how many cubic feet per minute (CFM) you need to remove a given amount of heat. As these are difficult to apply in AV work, I have found it is easier to think about minutes between air changes. Change the air in a home theater system every few minutes and problems go away.

Quiet, effective cooling is achieved by allowing all enclosures to breathe freely, to let air pass through slowly, and therefore quietly, and by being certain that the airflow flows where it should - over the hot equipment!

Unenclosed Installation Recommendations

There are many types and styles of cooling devices, and the particular installation and size dictate which of these would be most effective for the situation. Generally, these are good rules to follow:

If the equipment is not completely enclosed, but is on a bookshelf, in a corner, or otherwise has some, but not enough, ventilation (i.e. a cabinet with no back, no doors), use a cooling device that sits below or on top.

Use a cooling-base type device that sits underneath the equipment if the component has bottom slots, or a top-mounted fan unit if the vent openings are on top. If you want to put a heat-sensitive device, like a DVD player, on top of something hot, use a cooling-shelf ("heat-shield") product, and cool the "something hot" while shielding the device placed on top - this lets you put more gear in a given area than you safely could ordinarily.

Enclosed Installation Recommendations

If the equipment generates a moderate amount of heat, and if the enclosure is compact, a small system-type cooling package is the solution. A computer in a kitchen cabinet, or small music systems in a section of a larger cabinet are examples. In these cases, look for a cooling product with a couple of fans and grilles. These devices can be used to either pull in cool air, or push out the hot.

If the enclosure is mid-size (24"-30" high and one- or two-components wide) and the equipment is the typical home theater assortment of a receiver or amp, DVD player, a cable or satellite box, etc., there are larger system kits available to address the size and complexity of the configuration. Quality system sets will include multiple slow-turning fans, grilles, power supplies, and a control device. They should be heat sensitive and able to automatically adjust to environment and usage temperature changes with fan speed controlled by, or (better yet) proportional to, temperature rise.

If the system is more ambitious, with a whole-house amp, TiVo, power conditioner, etc., look for a still larger version of the system kits with full four-fan versions of the same automatic temperature sensitive cooling systems.

For the larger jobs, such as closets and enclosed video projectors, where you have to move the hot air up into an attic or dead space, use a system that states it is specially designed for and suitable for converted coat closets, enclosed single-chip (up to about 500 watt) projectors, and large cabinets that are about the same size as coat closets.

Finally, for the largest jobs (and the most power-hungry video projectors), there are serious commercial air handlers capable of moving air tens of feet to utility areas where it can dissipate.

More Tips

Fans can be mounted in various positions, while moving air in patterns that will produce reasonable ventilation, depending on availability of space behind or beside cabinets, or the presence of feet or a kick-panel, etc. If the equipment is on shelves, put holes in the shelves under the gear. If it is a rack installation, leave some open space in the rack, using vent panels. This lets cool air get in and around the equipment; so heated air can leave the rack and be removed from the enclosure. Try to get complex air motion; side to side, down to up, front to back. If fans will be visible when installed (on a wood cabinet) and "looks count", consider products made from matching woods that are now available.

Best Advice

As you can see, moving air successfully in order to cool your jets, so to speak, is a precise undertaking but, done correctly, it adds stability, performance and safety to any home or office electronics installation. The best advice is to look for products from a company that specializes in cooling. And finally, if the system and the installation is a bit too complicated for even the most astute do-it-yourselfer, don't hesitate to involve a licensed system integrator who, again, has cooling and ventilating as a specialty or a significant business group dedicated to this area.

For more information on cooling systems and products, or if there are questions you still need answered, feel free to ask me at frankf@activethermal.com. It's cool! 

Comments (0)

This post does not have any comments. Be the first to leave a comment below.

Post A Comment

You must be logged in before you can post a comment. Login now.

Featured Product

PureLink - HCE III TX/RX: 4K HDR over HDBaseT Extension System w/ Control and Bi-Directional PoE

PureLink - HCE III TX/RX: 4K HDR over HDBaseT Extension System w/ Control and Bi-Directional PoE

The HCE III Tx/Rx HDBaseTâ„¢ extension system offers full HDMI 2.0 compliance supporting HDR (High Dynamic Range) and 4K@60Hz with 4:4:4 chroma sampling. Featuring PureLink's proprietary Pr©cis codec, a light compression technology, the HCE III can transport Ultra HD/4K, multi-channel audio, and High Dynamic Range (10 bits support) content over a single CATx cable. The HCE III provides HDMI extension up to 130 feet (40 meters) at Ultra HD/4K and up to 230 ft. (70 meters) at 1080p over category cable with embedded multi-channel audio, CEC pass-through, bi-directional RS-232 and IR control, and PoE - all with zero loss and zero noise. The HCE III Tx/Rx also supports Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio plus LCPM (up to 192 kHz). Additionally, the low profile "slim box" enclosure design make the HCE III ideal for limited space installation environments, such as behind flat panel displays and video walls.