In our previous articles here on HomeToys, we have presented some simple monitoring solutions for use with your home computer and the internet services at www.BroadbandSentry.com. In this article we will introduce the addition of remote control to the client software from BroadbandSentry.

Remote control your home via the Internet using Web services with inexpensive AC wireless controller

Gary Drake | BroadbandSentry

Remote control your home via the Internet
using Web services with inexpensive AC wireless controllers.

By Gary Drake www.BroadbandSentry.com

In our previous articles here on HomeToys, we have presented some simple monitoring solutions for use with your home computer and the internet services at www.BroadbandSentry.com. In this article we will introduce the addition of remote control to the client software from BroadbandSentry.


 From the article in the October issue at HomeToys titled No cost / Low cost Web based monitoring system using your computer, and a free web based service from BroadBandSentry --- a serial port on your computer can be used to create a very cost effective monitoring system.

Now we have added to the remote client the ability to modify the state of the control lines in that serial port.

                 RS-232 SERIAL (COM) PC PORT CONNECTOR DB-9 

DB-9 PIN (Male) FUNCTION ABBREVIATION

         1

 Data Carrier Detect 

CD

          2 

 Receive Data   

RD or RX

          3

Transmitted Data     

TX or TD

          4

   Data Terminal Ready 

DTR

          5

  Signal Ground    

GND

          6

  Data Set Ready    

 DSR

          7

   Request To Send   

 RTS

          8

Clear To Send     

CTS

          9

 Ring Indicator   

RI

DTR and RTS are controllable pins on the RS-232 port, we have added the ability to control them remote using www.BroadBandsentry.com. The Web based interface now allows for the setting or clearing of the state of DTR and RTS, as well requesting a pulsing of these two lines.

RS-232 uses a +12 volt to -12 volt range at it's maximum swing, and will change states in a narrow range +5 volts to - 5 volts. There are numerous web pages with all the details, a web search with your favorite search engine should supply all the details you might require. But for now we will assume we have a serial port that is working from the +12 to -12 range.  Which on my computers actually turns out to be a around -11.3 to -11.3 volts. We have this DC voltage and live in a AC world, lights, fans, pump motors, etc. often are 110 volt AC, or 220 AC, so how to control them? Quite simply go wireless! Several companies offer wireless AC control modules with remote controls much like a car door opener. www.RadioShack.com offer Wireless AC Outlet Controllers, and www.skylinkhome.com offers similar products. These products consists of a small remote, much like you would have for your car or garage door opener, and a module that plugs into an AC outlet, providing a controllable outlet.

The remotes uses a 12 volt battery for it's power source, conveniently close to the voltage found on a RS-232 RTS or DTR pin.  To remotely control the remote, we can simply remove the battery, place a diode between the RTS/DTR pin and the plus side of the battery input to keep the supplied voltage from going negative, remember that RS-232 swings from +12 to -12 volts. Connect the negative side of the battery connection to the ground on the RS-232 connector (pin 5 on a 9 pin RS-232 connector). The remote is now controllable from the serial port.  Using the remote client from www.Broadbandsentry.com the DTR/RTS pin can be toggled, the on time can be set for this pulse.

 

The remote used above does not have a selectable transmission code as you would find on garage door opener, and should be considered very insecure, fortunately www.skylinkhome.com offers a line of wireless remote products that offer a user selectable operation code. These products allow for more then one receiver be controlled as well. In a single receiver application the technique used above can be used, solder across the switch forcing it to be allows depressed, then modify the connections to the battery. If your application requires two receivers, then the power source will remain the battery and relays are used to act as the switches, please see www.Broadbandsentry.com for details.

These wireless devices are part of the F.C.C. part 15, which allows for user to individually modify a device with out requiring certification. To understand the details of the regulations the particular device  you are experimenting with the link below can be used to lookup the F.C.C. ID number.

https://gullfoss2.fcc.gov/prod/oet/cf/eas/reports/GenericSearch.cfm

The complete text of F.C.C. regulations can be found at:
http://www.fcc.gov/oet/info/rules/

Please make a point of researching what portion of the F.C.C. rules the device you are experiment with fit, the amount of time you are allowed to transmit maybe restricted. For some of the devices used in this article the transmit time is very limited and must be taken into account in your implementation.

As with all devices that can start automatically remember to include in your planning interlocks to prevent unexpected operation due to any cause. Having an object move because a motor turned on can cause injury if safety is not properly considered!!!!!!!

These remote devices offer a solution for remotely sensing a event of interest. Want to sense a door (garage door for example) opening, window, gate but it's not convenient to run ethernet or other wires to it. Then use the remote and a wall module that supports a relay connection. www.skylinkhome.com offers a module that is sold as a replacement remote garage door opener. This wall module opens and closes a relay as commanded by the remote.

 

The connection to the relay, the small open on the side of the wall module, can be used to open or close one of the status pins on your serial port. One side of the connection is to the GND (5) pin the other side can be connected to any of the status pins. With the client software from www.BroadbandSentry.com  the configuration is set on the web to sense a change to the status pin chosen. Messages, control signals to other wireless modules can be configured.

For more details on the Web based service by www.BroadbandSentry.com please visit our web site and our previous articles.

Home Monitoring Network - December - 2004
Web based monitoring system - October - 2004
Web Enabled Monitoring System - August - 2004
Internet based Monitoring - June - 2004


Comments (0)

This post does not have any comments. Be the first to leave a comment below.


Post A Comment

You must be logged in before you can post a comment. Login now.

Featured Product

Light sockets; Not just for lights anymore

Light sockets; Not just for lights anymore

Smart Bulbs are out there and they can do far more then just provide light. Speakers, projectors, wi-fi extenders and more. The standard light socket that is wired up and ready to go in nearly every home in North America is now providing an easy and affordable option for home owners and renters alike to enter into the world of the "Smart Home". Here is a look at some of the Smart Bulbs and Smart Lighting options out there, and this list is just the beginning. In this ongoing article we hope to continue to add to and grow this list, so stay tuned!