In concept we have tried to present simple interfaces and simple hardware requirements, in essence a thin client approach. Web based services to support the notification systems, and simple local clients, some software, some hardware.

Create a wireless sensor network using WIFI and web services.

Gary Drake | BroadbandSentry

Create a wireless sensor network
using WIFI and web services.
By Gary Drake www.BroadbandSentry.com

In concept we have tried to present simple interfaces and simple hardware requirements, in essence a thin client approach. Web based services to support the notification systems, and simple local clients, some software, some hardware.


Using low cost hardware available from retail vendors a wireless sensor network can be constructed using WIFI. In a earlier article here in home toys "Adding some simple monitoring tools, and Internet ready devices, your existing network connection brings your real world to your wired world.", we described using simple print servers to create a sensor. In this article we will extend the same concept to create a wireless sensor system. We will be building upon the SNMP (simple network management protocol) supported by a number of low cost print servers both wireless and wired available from a number of retail network hardware vendors. These devices send a short status message to a specified IP address, it does not have to be accessible from outside your network, no open ports, with simple web based setup!

By combining www.Broadbandsentry.com, low cost SNMP enabled wireless print servers and a web browser you can create an easy to implement wireless sensor network. Wireless print servers like the DP-311P from D-Link (www.D-link.com) combine both the web page interface that we used in our previous articles, with an added ability to send SNMP alert messages. These messages are sent when the device changes state from online to offline, and also sent when going from online to out of paper. Very limited true, but one DP-311P can be configured to watch for two major events in your home or office, HEAT and WATER! Going back and looking at "Adding some simple monitoring tools, and Internet ready devices, your existing network connection brings your real world to your wired world", we described some easy to assemble sensors for both water and temperature. The Temperature sensor can be constructed completely from components available at any home supply center. The water sensor requires a float switch that can be obtained from an electronics supply site.

Water Sensor

                

Temperature

Door and Window Switches

Using one or more SNMP enabled print servers we can construct a network of sensors connected both wireless with WIFI and wired. Once we have a sensor network the next problem is of course to do something with the information, SNMP is well established in the networking world, a great source for information and resources can be found at www.SNMPlink.org. Bringing us to the service www.BroadbandSentry.com offers. We have added support for receiving SNMP alerts from print servers from a number of vendors (www.D-link.com, www.netgear.com, and more). This service work much like what we have described in our previous articles here at Home toys, this is perhaps the simplest of all!

Set your printer server's SNMP settings following the instruction from the www.BroadbandSentry.com web site as you configure the alert messaging options. The last message received from your device is viewable on www.BroadbandSentry.com allowing for easy testing of your configuration. Only the short SNMP message is sent from your printer server to www.BroadbandSentry.com's SNMP server.

We at www.Broadbandsentry.com have been working on creating a simple to use, lowest cost, home/office networked monitoring and control solution. If you refer back to the other articles we have written here at www.HomeToys.com:

In concept we have tried to present simple interfaces and simple hardware requirements, in essence a thin client approach. Web based services to support the notification systems, and simple local clients, some software, some hardware. All as simple and low cost as possible. The new SNMP service from  www.BroadbandSentry.com extends this concept allowing for the creation of wireless sensor and control networks with readily available low cost retail equipment. More details can be found at www.BroadbandSentry.com


Comments (0)

This post does not have any comments. Be the first to leave a comment below.


Post A Comment

You must be logged in before you can post a comment. Login now.

Featured Product

ELK Products -C1M1 Dual-Path Alarm Communicators with Remote Services

ELK Products -C1M1 Dual-Path Alarm Communicators with Remote Services

C1M1 offers a truly significant reduction in transmission time in comparison to other communicators that rely on dial capture or data bus decoding. This can result in quicker response time to emergency situations which could save lives and assets. By providing both IP and cellular pathways, C1M1 provides the reliability installers are looking for in an alarm communicator. C1M1 eliminates port forwarding and extra fees for remote access. Installers can remotely upload/download programming changes to M1 controls over IP or cellular using ElkRP2. Consumers can control the M1 remotely via the free ElkLink mobile app and web portal, as well as eKeypad and M1 Touch Pro apps. Other IP-based software and interface partners can connect to the M1 control over the local network through C1M1. C1M1 also provides email/text notifications for arm, disarm, and alarm events. ELK-C1M14GSM supports GSM (AT&T/T-Mobile) networks and ELK-C1M1CDMA supports CDMA (Verizon) networks.